Eagle Anchor EG／SEG

Eagle Anchor　EG／SEG

For concrete / Injection method

Internal thread anchor for adhesive anchor injection method.
Maximizes the ability of the adhesive and firmly fixes it in the concrete hole.
Unique feature of internal thread for unevenness correction. Attachment and detachment of fixtures is also possible.

［Application］

Installation for Bench/ Temporary Rail/ Soundproof Wall, etc.

Installation Procedure

❶Drill a hole

❷Clean the hole 2~3 times

❸Inject the material and carefully insert the Eagle Anchor while rotating it

❹After curing, insert the threaded rod. Installation complete

●We also have a designated installation cap for inserting Eagle Anchor alone into the pilot hole.

To install the equipment:

Use bolts equivalent to SS400 for steel EG type and bolts equivalent to SUS304 for stainless steel SEG type.

Estimated Injection Amount

Item no.	Required resin amount	Estimated no. of shots
Item no.	Required resin amount	EA・EX	SE
EG/SEG-10	8cc	3	1
EG/SEG-12	17cc	6	2
EG/SEG-16	40cc	14	4
EG/SEG-20	54cc	18	6
EG/SEG-22	102cc	34	11
EG/SEG-24	140cc	47	14
EG/SEG-10S	7cc	3	1
EG/SEG-12S	13cc	5	2
EG/SEG-16S	31cc	11	4
EG/SEG-20S	41cc	14	5
EG/SEG-22S	70cc	24	7
EG/SEG-24S	114cc	38	12
EG/SEG-30WS	7cc	3	1
EG/SEG-30W	8cc	3	1
EG/SEG-40WS	13cc	5	2
EG/SEG-40W	17cc	6	2

※The dispensing rate might change depending on the installation temperature conditions, so use this as a guide

Estimated Working / Curing time

EA-350/EA-500/EA-500S

Temperature	−5℃	0℃	5℃	10℃	20℃	30℃	40℃
Working time（EA-350）	4hrs	2hrs	40min	25min	10min	3min	1.5min
Working time（EA-500・500S）	5hrs	2hrs	1hr	35min	10min	3min	1.5min
Curing time	8hrs	4hrs	3hrs	1.5hrs	30min	25min	10min

EA-500W (For installation in low temperature environment)

Temperature	−15℃	−10℃	−5℃	0℃	5℃	10℃
Working time	2hrs	1hr	30min	15min	10min	5min
Curing time	6hrs	3hrs	2hrs	1hr	30min	20min

EX-350/EX-400L

Temperature	5℃	10℃	20℃	30℃	40℃
Working time	2hrs	1.5hrs	40min	25min	12min
Curing time	24hrs	16hrs	8hrs	5hrs	3hrs

※This curing time is a guideline for achieving about 80% of max. strength

SE-550

Temperature	5℃	20℃	30℃
Working time	70min	35min	20min
Curing time	8hrs	6hrs	4hrs

※Curing time is the time it takes for compressive strength to develop
※The working time depends on the ambient temperature used

Mechanical Properties

EG/SEG Type

強度表をPDFで開く

Thread	D	Drilling depth	Max. load
		Unit：mm	Unit：kN
Thread	D	Drilling depth	Tensile strength
M10	14.0	55	19.2
M10	14.0	65	22.1
M12	18.0	70	28.8
M12	18.0	95	38.6
M16	24.0	85	54.9
M16	24.0	115	61.8
M20	28.0	105	89.4
M20	28.0	145	108.8
M22	32.0	114	112.3
M22	32.0	170	138.5
M24	36.0	150	131.0
M24	36.0	200	164.7
W3/8	14.0	55	19.2
W3/8	14.0	65	22.1
W1/2	18.0	70	28.0
W1/2	18.0	95	38.6

・Fc=21N/mm² concrete
・The above load data is the value when using EX-350 / SE-550 with all threaded rod (equivalent to SS400)

Size Chart

EG TYPE: STEEL / TRIVALENT CHROMATE COATING

サイズ表をPDFで開く

Open chart in PDF

							Unit：mm		Unit：pc
Thread	Item no.	D	L	ℓ	Drilling diameter		Drilling depth	Qty・per
Thread	Item no.	D	L	ℓ	EA・EX	SE	Drilling depth	Box	Carton
M10	EG-10S	14.0	55	15	16.0	18.0	55	50	200
M10	EG-10	14.0	65	18	16.0	18.0	65	50	200
M12	EG-12S	18.0	70	20	20.0	22.0	70	25	100
M12	EG-12	18.0	95	23	20.0	22.0	95	25	100
M16	EG-16S ※	24.0	85	27	28.0	28.0	85	20	80
M16	EG-16	24.0	115	27	28.0	28.0	115	8	32
M20	EG-20S ※	28.0	105	35	32.0	32.0	105	6	24
M20	EG-20	28.0	145	35	32.0	32.0	145	6	24
M22	EG-22S ※	32.0	114	40	38.0	38.0	114	6	24
M22	EG-22	32.0	170	40	38.0	38.0	170	6	18
M24	EG-24S ※	36.0	150	45	42.0	42.0	150	4	16
M24	EG-24	36.0	200	45	42.0	42.0	200	4	12
W3/8	EG-30WS	14.0	55	15	16.0	18.0	55	50	200
W3/8	EG-30W	14.0	65	18	16.0	18.0	65	50	200
W1/2	EG-40WS	18.0	70	20	20.0	22.0	70	25	100
W1/2	EG-40W	18.0	95	23	20.0	22.0	95	25	100

※It will be a made-to-order product
※Please note that the drilling diameter is different when using the Seismic Eco-filler SE-550

SEG TYPE: STAINLESS STEEL SUS304