AR Chemical Setter IS System EA／EA-S

AR Chemical Setter IS System　EA／EA-S

For Concrete, Rock, ALC / Cartridge type

Demonstrates high adhesion strength.
Free drilling conditions, easy to construct long holes.
Can be installed even at low temperatures of -5°C.
Fast curing time and sufficient working life.
Can be installed on walls and ceilings.

［Application］

Construction for Building / Equipment / Road・Railway / Tunnel, etc.

Installation Procedure

❶Drill a hole

❷Clean the hole 2 to 3 times

❸Mark the anchor rod

❹Resin injection

※Be sure to discard the first 3~4 shots.

⚫Be sure to clean the dust in the hole by brush.
⚫Completely remove the water that has accumulated in the holes (wet holes are possible).
⚫At the beginning of use, the mixing of the main agent and the hardener will be uneven, resulting in the inability to exert strength. Be sure to discard the first 3~4 shots.
⚫Do not touch the anchor rods during the curing time.
⚫When installing on the wall or ceiling, be careful of liquid dripping.
⚫Be sure to check the expiration date (1 year from manufacture).

❺Insert the rod while gently turning it by hand. Installation after curing

Estimated Working / Curing Time

EA-350/EA-500/EA-500S

Temperature	−5℃	0℃	5℃	10℃	20℃	30℃	40℃
Working time （EA-350）	4hrs	2hrs	40min	25min	10min	3min	1.5min
Working time （EA-500・500S）	5hrs	2hrs	1hr	35min	10min	3min	1.5min
Curing time	8hrs	4hrs	3hrs	1.5hrs	30min	25min	10min

EA-500W（For installation in low temperature environment）

Temperature	−15℃	−10℃	−5℃	0℃	5℃	10℃
Working time	2hrs	1hr	30min	15min	10min	5min
Curing time	6hrs	3hrs	2hrs	1hr	30min	20min

・Working time: The time from the start of resin injection until the resin loses fluidity (insert the rod within this time)
・Curing time: Until able to load (do not touch the rod between working and cure time)

Mechanical Properties

[For embed. length 8d]

Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Allowable tensile load (long term)	Allowable tensile load (short term)
		unit:mm		unit:kN
M8	9.0	70	5.9	8.9
M10	12.0	80	9.0	13.5
M12	14.0	100	13.5	20.3
M16	18.0	130	23.5	35.2
M20	23.0	160	36.1	54.2
M22	25.0	180	44.7	67.1
M24	28.0	190	51.5	77.3
M30	35.0	240	71.1	106.7
M36	42.0	290	92.8	139.3
M42	52.0	340	117.5	176.2
M48	60.0	380	139.7	209.6

[埋込長8dの場合]

Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Allowable tensile load (long term)	Allowable tensile load (short term)
		unit:mm		unit:kN
D6	9.0	70	4.7	7.1
D10	12.0	80	9.0	13.5
D13	16.0	100	14.7	22.0
D16	20.0	130	23.5	35.2
D19	24.0	160	34.3	51.5
D22	28.0	180	44.7	67.1
D25	32.0	190	52.5	78.8
D32	40.0	240	71.7	107.5
D38	48.0	290	93.5	140.3
D41	55.0	340	117.1	175.7
D51	65.0	380	140.9	211.4

[For embed. length 6d]

Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Allowable tensile load (long term)	Allowable tensile load (short term)
		unit:mm		unit:kN
M8	9.0	50	3.8	5.8
M10	12.0	60	5.6	8.4
M12	14.0	70	7.6	11.5
M16	18.0	100	15.5	23.2
M20	23.0	120	22.4	33.7
M22	25.0	130	26.4	39.6
M24	28.0	140	30.7	46.1
M30	35.0	180	50.6	75.9
M36	42.0	220	65.5	98.3
M42	52.0	250	78.4	117.7
M48	60.0	290	96.8	145.2

・The allowable tensile load varies depending on the bolt material, type, concrete strength, and embedding conditions, so please perform strength calculations according to the actual installation conditions.
・The allowable tensile load is a calculated value using the manufacturer’s formula. (Concrete strength Fc=21N/㎟. M screw (SS400), threaded rod / deformed bar (SD295 (SD345 for D19 and above))

[埋込長6dの場合]

Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Allowable tensile load (long term)	Allowable tensile load (short term)
		unit:mm		unit:kN
D6	9.0	50	3.3	5.0
D10	12.0	60	5.6	8.4
D13	16.0	70	7.7	11.6
D16	20.0	100	15.5	23.2
D19	24.0	120	22.3	33.4
D22	28.0	130	26.4	39.6
D25	32.0	140	30.9	46.3
D32	40.0	180	51.0	76.6
D38	48.0	220	66.0	99.1
D41	55.0	250	78.1	117.2
D51	65.0	290	97.8	146.7

Installation Example

EA TYPE: NON-STYRENE EPOXY ACRYLATE RESIN

…SHASE-S Standard

サイズ表をPDFで開く

［For embed. length 8d］

Open chart in PDF

			Unit:mm	Unit:㎤			Unit：pc
Embed. length	Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Required resin amount	No. of anchoring installations per cartridge
Embed. length	Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Required resin amount	EA-350	EA-500	EA-500S
8d	M8	9.0	70	2.3	130	194	52
8d	D6	9.0	70	2.7	111	164	44
8d	M10	12.0	80	5.3	56	83	22
8d	D10	12.0	80	4.0	87	109	30
8d	M12	14.0	100	8.3	36	52	14
8d	D13	16.0	100	8.9	33	49	13
8d	M16	18.0	130	15.2	19	28	7
8d	D16	20.0	130	18.0	16	24	6
8d	M20	23.0	160	32.7	9	13	3
8d	D19	24.0	160	31.8	9	13	3
8d	M22	25.0	180	40.5	7	10	2
8d	D22	28.0	180	49.3	6	8	2
8d	M24	28.0	190	59.8	5	7	2
8d	D25	32.0	190	67.7	4	6	1
8d	M30	35.0	240	115.6	2	3	1
8d	D32	40.0	240	133.2	2	3	Requires 2 cartridges
8d	M36	42.0	290	197.9	1	2	Requires 2 cartridges
8d	D38	48.0	290	233.1	1	1	Requires 2 cartridges
8d	M42	52.0	340	409.6	Requires 2 cartridges	1	Requires 4 cartridges
8d	D41	55.0	340	422.7	Requires 2 cartridges	1	Requires 4 cartridges
8d	M48	60.0	380	618.1	Requires 2 cartridges	Requires 2 cartridges	Requires 5 cartridges
8d	D51	65.0	380	588.9	Requires 2 cartridges	Requires 2 cartridges	Requires 5 cartridges

［For embed. length 6d］

表をPDFで開く

			Unit:mm	Unit:㎤			Unit：pc
Embed. length	Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Required resin amount	No. of anchoring installations per cartridge
Embed. length	Threaded rod / Deformed bar	Drilling diameter	Drilling depth	Required resin amount	EA-350	EA-500	EA-500S
6d	M8	9.0	50	1.7	176	258	75
6d	D6	9.0	50	2.0	150	220	60
6d	M10	12.0	60	4.0	75	110	30
6d	D10	12.0	60	3.1	96	141	38
6d	M12	14.0	70	5.9	50	74	20
6d	D13	16.0	70	6.3	43	69	19
6d	M16	18.0	100	11.7	25	37	10
6d	D16	20.0	100	13.9	21	31	8
6d	M20	23.0	120	24.6	12	17	4
6d	D19	24.0	120	23.9	12	18	5
6d	M22	25.0	130	29.4	9	13	3
6d	D22	28.0	130	35.7	7	11	3
6d	M24	28.0	140	44.2	6	9	3
6d	D25	32.0	140	50.0	5	8	2
6d	M30	35.0	180	86.7	3	5	1
6d	D32	40.0	180	99.9	3	4	1
6d	M36	42.0	220	150.1	1	2	Requires 2 cartridges
6d	D38	48.0	220	176.8	1	2	Requires 2 cartridges
6d	M42	52.0	250	301.2	Requires 2 cartridges	1	Requires 3 cartridges
6d	D41	55.0	250	310.8	Requires 2 cartridges	1	Requires 3 cartridges
6d	M48	60.0	290	471.0	Requires 2 cartridges	Requires 2 cartridges	Requires 4 cartridges
6d	D51	65.0	290	449.4	Requires 2 cartridges	Requires 2 cartridges	Requires 4 cartridges

・The required amount of resin is a value calculated with a surplus rate of 20%.
・The number of installations per cartridge is a guide. (Upper: M screw; Lower: deformed bar)

The IS system EA-350 / 500 / 500S does not require stirring by rotating or striking the anchor rods, so it can be embedded in various shapes and materials. However, do not use a round bar or other object with a smooth surface, as it will not be able to exert sufficient fixing strength.

◦When storing the EA-350 in use, attach the mixing nozzle, store the foil pack in the cartridge holder in a cool and dark place, and must be used up within 4 weeks.
For EA-500 / EA-500S / EA-500W, remove the mixing nozzle and wipe off the resin adhering to the tip of the cartridge. Finally, attach the cap, store it in a cool and dark place, and use it up within the expiration date.
◦When reusing, make sure that the resin at the tip of the cartridge is not cured before replacing it with a new mixing nozzle. If the resin is cured, remove the cured resin before installing the mixing nozzle.

Packing

EA-350（Content：350cm³）

Product name	Item no.	Content

Resin set	EA-350	1 resin cartridge 2 mixing nozzles
Optional mixing nozzle	MX-EA350	10 pieces per bag
Optional holder	HD-350	－
Optional cartridge holder	DM-350	1 dispenser 1 holder
Cordless dispenser	DJ-AX2	－
Air dispenser	DP-350	－

EA-500・EA-500W（Content：500cm³）

Product name	Item no.	Content

Base kit	EA-500-B	1 resin cartridge 1 dispenser 2 mixing nozzles Kit storage bag
Resin set	EA-500	1 resin cartridge 2 mixing nozzles
Resin set	EA-500W	1 resin cartridge 2 mixing nozzles
Optional mixing nozzle	MX-EA5	10 pieces per bag
Air dispenser	DP-EA5	－
Manual dispenser	DM-EA5	－

※The dispenser of the base kit is a manual type

EA-500S（Content：150cm³）

Product name	Item no.	Content

Resin set	EA-500S	1 resin cartridge 1 mixing nozzle 1 adapter
Optional mixing nozzle	MX-EA5S	10 pieces per bag
Recommended dispenser	DM-EA5S	－

Product Details