Fastener Products

Product Details

AR Chemical Setter IS System　EX／EX-L

For Concrete, Rock / Cartridge type
  • By adding thixotropy, it can be installed in the direction of walls and ceilings.
  • Compatible with rods with wide range of shapes and materials.
  • Easy to install in long holes.
  • The mixture of the main agent and the curing agent can be visually confirmed.
  • Can also be used in wet holes.
［Application］
Installation for Chimney Foundation / Rockfall Prevention Net/ Rail Bracket

❶Drill a hole
❷Clean 2 to 3 times
❸Mark the anchor rod
❹Resin injection
※Be sure to discard the first 3-4 shots.
⚫Do not use in an environment below 5 ° C as the strength will be extremely reduced.
⚫Be sure to clean the dust in the hole by brush.
⚫Completely remove the water that has accumulated in the holes (wet holes are possible).
⚫At the beginning of use, the mixing of the main agent and the hardener will be uneven, resulting in the inability to exert strength. Be sure to discard the first 3~4 shots.
⚫Do not touch the anchor rods during the curing time.
⚫When installing on the wall or ceiling, be careful of liquid dripping.
⚫Be sure to check the expiration date (1 year and 3 months from the time of manufacture).
❺Insert the rod while slowly turning it by hand. Installation complete.

EX-350/EX-400L

Temperature 5℃ 10℃ 20℃ 30℃ 40℃
Working time 2hrs 1.5hrs 40min 25min 12min
Curing time 24hrs 16hrs 8hrs 5hrs 3hrs
・Working time: The time from the start of resin injection until the resin loses fluidity (insert the rod within this time).
・Curing time: Until able to load (do not touch the rod between working and cure time).

[For embed. length 10d]

unit:mm unit:kN
Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
M8 9.0 80 5.9 8.6
M10 12.0 100 9.4 14.2
M12 14.0 120 13.7 20.6
M16 18.0 160 25.6 38.4
M20 23.0 200 38.3 57.5
M22 25.0 220 47.4 71.2
M24 28.0 240 55.3 82.9
M30 35.0 300 87.8 131.8
M36 42.0 360 124.9 187.4
M42 52.0 420 158.7 238.1
M48 60.0 480 196.6 294.9

[埋込長8dの場合]

unit:mm unit:kN
Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
D6 9.0 80 6.2 9.3
D10 12.0 100 14.0 21.0
D13 16.0 120 21.3 32.0
D16 20.0 160 37.7 56.5
D19 24.0 200 54.2 81.3
D22 28.0 220 61.7 92.5
D25 32.0 240 69.6 104.5
D32 40.0 300 95.8 143.7
D38 48.0 360 125.0 188.5
D41 55.0 420 158.3 237.5
D51 65.0 480 198.1 297.1

[For embed. length 8d]

unit:mm unit:kN
Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
M8 9.0 70 5.9 8.9
M10 12.0 80 9.4 14.2
M12 14.0 100 13.7 20.6
M16 18.0 130 25.4 38.1
M20 23.0 160 38.3 57.5
M22 25.0 180 47.4 71.2
M24 28.0 190 52.2 78.4
M30 35.0 240 71.1 106.7
M36 42.0 290 92.8 139.3
M42 52.0 340 117.5 176.2
M48 60.0 380 139.7 209.6
・The allowable tensile load varies depending on the bolt material, type, concrete strength, and embedding conditions, so please perform strength calculations according to the actual installation conditions.
・The allowable tensile load is a calculated value using the manufacturer’s formula. (Concrete strength Fc=21N/㎟. M screw (SS400), threaded rod / deformed bar (SD295 (SD345 for D19 and above))

[埋込長6dの場合]

unit:mm unit:kN
Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
D6 9.0 70 6.2 9.3
D10 12.0 80 9.6 14.4
D13 16.0 100 15.1 22.6
D16 20.0 130 25.4 38.1
D19 24.0 160 38.3 57.5
D22 28.0 180 48.6 73.0
D25 32.0 190 52.5 78.8
D32 40.0 240 71.7 107.5
D38 48.0 290 93.5 140.3
D41 55.0 340 117.1 175.7
D51 65.0 380 140.9 211.4

EX TYPE: BISPHENOL A/F TYPE EPOXY RESIN
[For embed. length 10d]

Unit：mm Unit：㎤ Unit：pc
Embed. length Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Required resin
amount		 No. of anchoring installations
per cartridge
EX-350 EX-400L
10d M8 9.0 80 2.6 115 –
10d D6 9.0 80 3.1 96 –
10d M10 12.0 100 6.7 44 –
10d D10 12.0 100 5.1 58 –
10d M12 14.0 120 10.1 29 84
10d D13 16.0 120 10.8 27 78
10d M16 18.0 160 18.8 15 45
10d D16 20.0 160 22.2 13 38
10d M20 23.0 200 41.0 7 20
10d D19 24.0 200 39.9 7 21
10d M22 25.0 220 49.6 6 17
10d D22 28.0 220 60.4 4 14
10d M24 28.0 240 75.7 3 11
10d D25 32.0 240 85.7 3 9
10d M30 35.0 300 144.5 2 5
10d D32 40.0 300 166.5 1 5
10d M36 42.0 360 245.6 1 3
10d D38 48.0 360 289.3 1 2
10d M42 52.0 420 505.9 2 cartridges required 1
10d D41 55.0 420 522.1 2 cartridges required 1
10d M48 60.0 480 780.8 2 cartridges required 1
10d D51 65.0 480 743.8 2 cartridges required 1
[For embed. length 8d]

Unit：mm Unit：㎤ Unit：pc
Embed. length Threaded rod /
Deformed bar		 Drilling
diameter		 Drilling depth Required resin
amount		 No. of anchoring installations
per cartridge
EX-350 EX-400L
8d M8 9.0 70 2.3 130 –
8d D6 9.0 70 2.7 111 –
8d M10 12.0 80 5.3 56 –
8d D10 12.0 80 4.1 73 –
8d M12 14.0 100 8.4 35 102
8d D13 16.0 100 9.0 33 95
8d M16 18.0 130 15.2 19 55
8d D16 20.0 130 18.0 16 47
8d M20 23.0 160 32.7 9 twenty five
8d D19 24.0 160 31.8 9 26
8d M22 25.0 180 40.5 7 20
8d D22 28.0 180 49.3 6 17
8d M24 28.0 190 59.8 Five 14
8d D25 32.0 190 67.7 Four 12
8d M30 35.0 240 115.6 2 7
8d D32 40.0 240 133.2 2 6
8d M36 42.0 290 197.9 1 Four
8d D38 48.0 290 233.1 1 3
8d M42 52.0 340 409.6 2 cartridges required 2
8d D41 55.0 340 422.7 2 cartridges required 2
8d M48 60.0 380 618.1 2 cartridges required 1
8d D51 65.0 380 588.9 2 cartridges required 1
・The required amount of resin is a value calculated with a surplus rate of 20%.
・The number of installations per cartridge is a guide. (Upper: M screw; Lower: Deformed bar)

Since the IS system EX-350 / 400L does not require stirring by rotating or striking the anchor bolt, it can be embedded in various shapes and materials.
However, do not use a round bar or other object with a smooth surface, as it will not be able to exert sufficient fixing strength.


◦When storing the EX-350 in use, attach the mixing nozzle, store the foil pack in the cartridge holder in a cool and dark place, and must be used up within 4 weeks.
For EX-400L, remove the mixing nozzle and wipe off the resin adhering to the tip of the cartridge. Finally, attach the cap, store it in a cool and dark place, and use it up within the expiration date.
◦When reusing, make sure that the resin at the tip of the cartridge is not cured before replacing it with a new mixing nozzle. If the resin is cured, remove the cured resin before installing the mixing nozzle.

EX-350（Content：350cm3）

Product name Item no. Content
Resin set EX-350 1 resin cartridge
1 mixing nozzle
Optional mixing nozzle MX-MID 10 pieces per bag
Optional cartridge holder HD-350 －
Dispenser ・ Holder set DM-350 1 dispenser
1 holder
Cordless dispenser DJ-AX2 －
Air dispenser DP-350 －

EX-400L（Content：900cm3）

Product name Item no. Content
Resin set EX-400L 1 resin cartridge
1 mixing nozzle
Optional mixing nozzle MX-EX4L 10 pieces per bag
Air dispenser #122739-20PF －

【Drilling】
Anchor Drill Bit [ADXⅡ-HEX Type] [ADXⅡ-MAX Type]
Click here for detail ☞
【Cleaning】
Dust Brush [W Type]
Click here for detail ☞
【Marking】
Dispenser for EX-350 (manual type)
Cordless dispenser for EX-350
【Injection】
Air dispenser for EX-400L (air type)