Seismic Eco-Filler SE

For concrete / Cartridge type

Can be used even on wet surfaces.
Can easily knead with a designated stirring rod (sold separately).
Cement-based, non-combustible.
Contributes to improving the working environment with no VOC gas or odor.
Just a little drip of the material when injecting horizontally or facing the ceiling.

［Application］

Maintenance, repair, Reinforcement Work / Ancillary Equipment, Machinery / Equipment Installation, Electrical ・ Communication Equipment, and other Equipment Work

Installation Procedure

❶Drill a hole

❷Clean inside the hole and check the drilling depth

❸Mark the anchor reinforcing bar

❹Material injection

❺Insert the rod while slowly turning it by hand. Installation complete.

Handling Method

❶Material input

Be sure to put ❶special water in the cartridge and then ❷powder.

❷Mixing

Using a special stirring rod, insert until the brim of the lid hits the cartridge, and stir.
※1 minute for SE-550
※30 seconds for SE-150

❸Discharge preparation

Set the piston in the cartridge. With the piston side down, remove the pedestal and cap and attach the nozzle.

❹Air discharge

When the discharge preparation is complete, set the designated dispenser and discharge the air with the nozzle facing up.

Estimated working / curing time

Environmental temperature	0℃	5℃	20℃	30℃
Working time	80min	70min	30min	20min
Curing time	24hrs	8hrs	6hrs	4hrs

※Curing time is the time it takes for compressive strength to develop
※The working time depends on the ambient temperature used

●This product is a single-use type.
●Please use powder and special water immediately after opening.
●After stirring, use within the working time.
●Do not touch the anchor reinforcing bar during the curing time.
●Do not add cement, sand, water, admixtures (agents), etc.
●Wear protective goggles, protective masks, and gloves when working.
●Store in a place that is not affected by direct sunlight or rainwater.
●Be sure to check the expiration date (2 years from the time of manufacture).

Compressive strength / adhesion strength of material

Test items	Test conditions	Measured value
Compressive strength	1 day	55.1N/㎟
Compressive strength	28 days	76.3N/㎟
Bending strength	1 day	9.3N/㎟
Bending strength	28 days	13.2N/㎟
Adhesion strength	anchor reinforcing bar: D13 embed. depth: 91 mm concrete strength: Fc = 21N / ㎟	23.3N/㎟

Installation Specifications

Seismic Eco-Filler SE-150/SE-550 Common Specifications

サイズ表をPDFで開く

Open chart in PDF

		Unit：mm	Unit：cc		Unit：pc	Unit：mm	Unit：cc	Unit：pc
Anchor reinforcing bar da	Drilling diameter	Embedded length 7da specifications				Embedded length 20da specifications
		Drilling length	Required volume※1	No. of installations per cartridge※2		Drilling length	Required volume※1	No. of installations per cartridge※2
		Drilling length	Required volume※1	SE-150	SE-550	Drilling length	Required volume※1	SE-550
M8	13	56	7	18	－	－	－	－
D8	13	56	7	21	－	－	－	－
M10	14	70	9	14	－	200	24	－
D10	16	70	11	11	－	200	32	－
M12	16	84	12	10	－	240	34	－
D13	18	91	14	9	35	260	40	12
M16	20	112	22	5	23	320	61	8
D16	22	112	25	5	20	320	70	7
M20	25	140	42	3	12	400	119	4
D19	25	133	33	4	15	380	94	5
M22	28	154	58	2	8	440	166	3
D22	28	154	43	2	11	440	121	4
M24	30	168	72	1	7	480	204	2
D25	32	175	63	1	8	500	179	2
M27	34	189	102	－	4	540	291	1
D29	38	203	120	－	4	580	343	1
M30	38	210	145	－	3	600	413	1
D32	40	224	125	－	4	640	356	1
M33	41	231	174	－	－	660	497	－
D35	45	245	187	－	－	700	533	－
M36	45	252	234	－	－	720	669	－
D38	48	266	214	－	－	760	611	－
M39	48	273	274	－	－	780	781	－
D41	51	287	243	－	－	820	692	－
M42	53	294	384	－	－	840	1095	－
D51	61	357	384	－	－	1020	1097	－

・The drilling diameter can be da+10mm. (please contact us for installation specifications other than those listed above)
※The required volume is a value calculated with a surplus rate of 20%
※The no. of anchoring installations per cartridge may vary depending on the construction work

Since the Seismic Eco-Filler does not require stirring by rotating and striking the anchor bolt, it can be embedded in various shapes and materials.
However, do not use a round bar or other object with a smooth surface, as it will not be able to exert sufficient fixing strength.

Packing

SE-150（Kneading amount：150cc）

Product name	Item no.	Content

Seismic Eco-Filler	SE-150	1 cartridge 1 nozzle 1 piston 1 bottle of designated water 1 bag of powder
Optional stirring rod set	SE-MX150-SET	1 designated stirring rod 1 cartridge for preventing material scattering

SE-550（Kneading amount：550cc）

Product name	Item no.	Content

Seismic Eco-Filler	SE-550	1 cartridge 1 nozzle 1 piston 1 bottle of designated water 1 bag of powder
Optional stirring rod set	SE-MX550-SET	1 designated stirring rod 1 cartridge for preventing material scattering 1 extrusion rod
Optional dispenser for exclusive use	SE-DM550	－

Product Details