All Anchor (Hammer Drive Anchor) C／SC／316SC／C-D Type

For concrete / Hammer the pin type

Easy to install by hammering the pin.
Easily understand whether it has been properly set.
Able to directly hammer on the fixture.
The thread and the anchor main body are in the same diameter.

［Application］

Installation for Handrail / Fence Support / Bracket / Equipment Rack / Rack, etc.

Installation Procedure

❶Drill a hole

⚫When drilling directly from the top of the mortar or fixture, make sure to add the thickness of the mortar or fixture to embedment depth.

❷Clean the dust

❸Hammer the anchor

⚫Hammer the pin vertically and make sure to hammer it until it touches the top of the main body.

❹Use spanners to tighten up

・Suggested installation torque

Thread		Installation torque N・m
M6	–	4	–
M8	W5/16	9	8
M10	W3/8	18	14
M12	W1/2	31	34
M16	–	80	–
M20	–	150	–

Mechanical Properties

C/SC/316SC/C-D Type

強度表をPDFで開く

Thread	Anchor diameter	Embed. depth	Max. load
		Unit：mm		Unit：kN
Thread	Anchor diameter	Embed. depth	Tensile strength	Shear strength
M6	6.0	30	3.9	6.3
M8	8.0	35	6.5	10.1
M10	10.0	40	10.2	16.0
M12	12.0	50	17.1	23.3
M16	16.0	60	29.9	47.9
M20	20.0	80	41.4	73.6
W5/16	8.0	35	6.9	10.1
W3/8	9.5	40	9.8	15.3
W1/2	12.7	50	18.0	24.7

・Fc=21N/mm2 concrete

C/SC/C-D Type

強度表をPDFで開く

Size	Thread	Embed. depth	Max. load
		Unit：mm		Unit：kN
Size	Thread	Embed. depth	Tensile strength	Shear strength
－	－	－	－	－
840	M8	25	4.9	10.1
1050	M10	30	7.2	15.7
1260	M12	40	13.9	22.2
1680	M16	50	21.5	42.0
2010	M20	60	29.4	61.0

・Fc=21N/mm2 concrete

Size Chart

C TYPE (METRIC THREAD): STEEL / TRIVALENT CHROMATE SURFACE TREATMENT

…JCAA Certified

サイズ表をPDFで開く

Open chart in PDF

								Unit：mm		Unit：pc
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Qty・per
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Box	Carton
M6	C-645	45	15	5	6.4	30	36	10	50	800
M6	C-660	60	20	20	6.4	30	36	10	50	800
M6	C-680	80	20	40	6.4	30	36	10	50	800
M8	C-840	40	15	5	8.5	25	33	12	50	800
M8	C-850	50	20	5	8.5	35	43	12	50	800
M8	C-860	60	20	15	8.5	35	43	12	50	400
M8	C-870	70	25	25	8.5	35	43	12	50	400
M8	C-890	90	25	45	8.5	35	43	12	50	400
M8	C-810	100	35	55	8.5	35	43	12	50	400
M10	C-1050	50	20	6	10.5	30	40	14	50	400
M10	C-1060	60	25	6	10.5	40	50	14	50	400
M10	C-1070	70	25	16	10.5	40	50	14	50	300
M10	C-1080	80	25	26	10.5	40	50	14	50	300
M10	C-1090	90	30	36	10.5	40	50	14	50	300
M10	C-1010	100	30	46	10.5	40	50	14	50	300
M10	C-1012	120	30	66	10.5	40	50	14	50	200
M10	C-1015	150	30	96	10.5	40	50	14	50	200
M12	C-1260	60	20	6	12.7	40	52	19	30	240
M12	C-1270	70	25	6	12.7	50	62	19	30	240
M12	C-1280	80	25	16	12.7	50	62	19	30	180
M12	C-1290	90	30	26	12.7	50	62	19	30	180
M12	C-1210	100	40	36	12.7	50	62	19	30	180
M12	C-1212	120	50	56	12.7	50	62	19	30	120
M12	C-1215	150	50	86	12.7	50	62	19	30	120
M16	C-1680	80	30	10	17.0	50	66	24	15	90
M16	C-1610	100	40	20	17.0	60	76	24	15	90
M16	C-1612	120	40	40	17.0	60	76	24	15	90
M16	C-1615	150	50	70	17.0	60	76	24	15	60
M16	C-1619	190	50	110	17.0	60	76	24	15	60
M20	C-2010	100	40	15	21.5	60	80	30	10	40
M20	C-2013	130	50	25	21.5	80	100	30	10	40
M20	C-2015	150	50	45	21.5	80	100	30	10	40
M20	C-2019	190	50	85	21.5	80	100	30	10	40
M20	C-2023	230	50	125	21.5	80	100	30	–	10

・With conical nut type
・Max. fixture thickness = L – Embed. depth – Conical nut height

C TYPE (INCH THREAD): STEEL / TRIVALENT CHROMATE SURFACE TREATMENT

サイズ表をPDFで開く

Open chart in PDF

								Unit：mm		Unit：pc
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Qty・per
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Box	Carton
W5/16	C-2550	50	20	5	8.5	35	43	12	50	800
W5/16	C-2570	70	25	25	8.5	35	43	12	50	400
W3/8	C-3060	60	25	6	10.0	40	50	14	50	400
W3/8	C-3080	80	25	26	10.0	40	50	14	50	300
W3/8	C-3090	90	30	36	10.0	40	50	14	50	300
W1/2	C-4070	70	25	6	13.5	50	62	21	30	240
W1/2	C-4090	90	30	26	13.5	50	62	21	30	180

・W5/16-W3/8 are with conical nut type
・W1/2 are with nut/washer type
・Drilling depth = Embed. depth + Min. major diameter of anchor
・Max. fixture thickness = L – Embed. depth – Conical nut height or (nut/washer)

SC TYPE: STAINLESS STEEL SUS304

…JCAA Certified

サイズ表をPDFで開く

Open chart in PDF

								Unit：mm		Unit：pc
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Qty・per
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Box	Carton
M6	SC-645	45	15	5	6.4	30	36	10	50	800
M6	SC-660	60	20	20	6.4	30	36	10	50	800
M6	SC-680	80	20	40	6.4	30	36	10	50	800
M8	SC-840	40	15	5	8.5	25	33	12	50	800
M8	SC-850	50	20	5	8.5	35	43	12	50	800
M8	SC-860	60	20	15	8.5	35	43	12	50	400
M8	SC-870	70	25	25	8.5	35	43	12	50	400
M8	SC-890	90	25	45	8.5	35	43	12	50	400
M8	SC-810	100	35	55	8.5	35	43	12	50	400
M10	SC-1050	50	20	6	10.5	30	40	14	50	400
M10	SC-1060	60	25	6	10.5	40	50	14	50	400
M10	SC-1070	70	25	16	10.5	40	50	14	50	300
M10	SC-1080	80	25	26	10.5	40	50	14	50	300
M10	SC-1090	90	30	36	10.5	40	50	14	50	300
M10	SC-1010	100	30	46	10.5	40	50	14	50	300
M10	SC-1012	120	30	66	10.5	40	50	14	50	200
M10	SC-1015	150	30	96	10.5	40	50	14	50	200
M12	SC-1260	60	20	6	12.7	40	52	19	30	240
M12	SC-1270	70	25	6	12.7	50	62	19	30	240
M12	SC-1280	80	25	16	12.7	50	62	19	30	180
M12	SC-1290	90	30	26	12.7	50	62	19	30	180
M12	SC-1210	100	40	36	12.7	50	62	19	30	180
M12	SC-1212	120	50	56	12.7	50	62	19	30	120
M12	SC-1215	150	50	86	12.7	50	62	19	30	120
M16	SC-1680	80	30	10	17.0	50	66	24	15	90
M16	SC-1610	100	40	20	17.0	60	76	24	15	90
M16	SC-1612	120	40	40	17.0	60	76	24	15	90
M16	SC-1615	150	50	70	17.0	60	76	24	15	60
M16	SC-1619	190	50	110	17.0	60	76	24	15	60
M20	SC-2010	100	40	15	21.5	60	80	30	10	40
M20	SC-2013	130	50	25	21.5	80	100	30	10	40
M20	SC-2015	150	50	45	21.5	80	100	30	10	40
M20	SC-2019	190	50	85	21.5	80	100	30	10	40
M20	SC-2023	230	50	125	21.5	80	100	30	–	10
W3/8	SC-3060	60	25	6	10.0	40	50	14	50	400
W1/2	SC-4070	70	25	6	13.5	50	62	21	30	240

・M6-M16/W3/8 are with conical nut type
・M20・W1/2 are with nut/washer type
・Max. fixture thickness = L – Embed. depth – Conical nut height or (nut/washer)

316SC TYPE: STAINLESS STEEL SUS316

サイズ表をPDFで開く

Open chart in PDF

								Unit：mm		Unit：pc
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Qty・per
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Box	Carton
M6	316SC-645	45	15	5	6.4	30	36	10	50	800
M8	316SC-850	50	20	5	8.5	35	43	13	50	800
M8	316SC-870	70	25	25	8.5	35	43	13	50	400
M10	316SC-1060	60	25	6	10.5	40	50	17	50	400
M10	316SC-1080	80	25	26	10.5	40	50	17	50	300
M10	316SC-1010 ※	100	30	46	10.5	40	50	17	50	300
M12	316SC-1270	70	25	6	12.7	50	62	19	30	240
M12	316SC-1290	90	30	26	12.7	50	62	19	30	180
M16	316SC-1610	100	40	20	17.0	60	76	24	15	90
M16	316SC-1612	120	40	40	17.0	60	76	24	15	90

・Nut/washer type
・Max. fixture thickness = L – Embed. depth – (nut/washer)
※Limited Stock. The type is discontinued

C-D TYPE (METRIC THREAD): STEEL / HOT-DIP GALVANIZING
SV SURFACE TREATMENT NAIL

…JCAA Certified

サイズ表をPDFで開く

Open chart in PDF

								Unit：mm		Unit：pc
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Qty・per
Thread	Item no.	L	ℓ	Max. fixture thickness	Drilling diameter	Embed. depth	Min. drilling depth	S	Box	Carton
M8	C-850D	50	20	5	8.5	35	43	13	50	800
M8	C-870D	70	25	25	8.5	35	43	13	50	400
M8	C-810D	100	35	55	8.5	35	43	13	50	400
M10	C-1050D	50	20	6	10.5	30	40	17	50	400
M10	C-1060D	60	25	6	10.5	40	50	17	50	400
M10	C-1080D	80	25	26	10.5	40	50	17	50	300
M10	C-1090D	90	30	36	10.5	40	50	17	50	300
M10	C-1010D	100	30	46	10.5	40	50	17	50	300
M10	C-1012D	120	30	66	10.5	40	50	17	50	200
M10	C-1015D	150	30	96	10.5	40	50	17	50	200
M12	C-1260D	60	20	6	12.7	40	52	19	30	240
M12	C-1270D	70	25	6	12.7	50	62	19	30	240
M12	C-1290D	90	30	26	12.7	50	62	19	30	180
M12	C-1210D	100	40	36	12.7	50	62	19	30	180
M12	C-1212D	120	50	56	12.7	50	62	19	30	120
M12	C-1215D	150	50	86	12.7	50	62	19	30	120
M16	C-1610D	100	40	20	17.0	60	76	24	15	90
M16	C-1612D	120	40	40	17.0	60	76	24	15	90
M16	C-1615D	150	50	70	17.0	60	76	24	15	60
M20	C-2013D	130	50	25	21.5	80	100	30	10	40
M20	C-2015D	150	50	45	21.5	80	100	30	10	40
M20	C-2019D	190	50	85	21.5	80	100	30	10	40
W3/8	C-3060D	60	25	6	10.0	40	50	17	50	400

・Nut/washer type
・Max. fixture thickness = L – Embed. depth – (nut/washer)

Conical Nut BN/SBN

BN TYPE: STEEL / TRIVALENT CHROMATE COATING

サイズ表をPDFで開く

Open chart in PDF

					Unit：mm		Unit：pc
Thread	Item no.	S	Nut height	Washer major diameter	Washer thickness	Qty・per
Thread	Item no.	S	Nut height	Washer major diameter	Washer thickness	Plastic bag	Carton
M6	BN-M6	10	5	14	1.0	50	6,500
M8	BN-M8	12	6.5	18	1.4	50	4,000
M10	BN-M10	14	8	22	1.6	50	2,000
M12	BN-M12	19	10	25	1.6	30	1,200
M16	BN-M16	24	13	32	2.3	15	450
M20	BN-M20	30	16	40	3.2	10	250
W5/16	BN-W25	12	6.5	18	1.4	50	4,000
W3/8	BN-W30	14	8	22	1.6	50	2,000

SBN TYPE: STAINLESS STEEL
NUT: SUSXM7/ WASHER: SUS304

サイズ表をPDFで開く

Open chart in PDF

					Unit：mm		Unit：pc
Thread	Item no.	S	Nut height	Washer major diameter	Washer thickness	Qty・per
Thread	Item no.	S	Nut height	Washer major diameter	Washer thickness	Plastic bag	Carton
M6	SBN-M6	10	5	14	1.0	50	6,500
M8	SBN-M8	12	6.5	18	1.3	50	4,000
M10	SBN-M10	14	8	22	1.5	50	2,000
M12	SBN-M12	19	10	25	1.8	30	1,200
M16	SBN-M16	24	13	32	2.3	15	450
W3/8	SBN-W30	14	8	22	1.5	50	2,000

Product Details