Fastener Products

Product Details

AR Chemical Setter　AP／AP-S／AP-L

For Concrete / Rotation ・Hammer-in type
  • Demonstrates outstanding alkaline resistance.
  • High initial rigidity and excellent toughness.
  • Size can be selected according to the purpose (standard, short, long).
  • Can be installed on walls and ceilings.
［Application］
Seismic Reinforcement (Steel Brace Installation) / Joint Bars for Extension and Reconstruction / RC Wall, Pillar, Beam Reinforcement / Soundproof Wall Installation / Bridge Collapse Prevention / Bridge Leg Reinforcement / Fender Installation / Levee Raising / Oblique Slope Slip Material for Ship Landing・Car Stop Installation / Mooring Post・Ring Installation / Guard Rail Installation, etc.

❶Drill a hole
❷Clean the hole 2 to 3 times
❸Mark the anchor rod
❹Insert and hammer in
⚫After embedment, the curing time of the resin differs depending on the temperature. Please check the table below. Also, do not move rods and reinforcing steels within the curing time.
⚫Please use the stopper for installation on the ceiling surface. The stopper is not included. Please order if necessary.
⚫Please be careful about liquid when installing on the wall and ceiling surface.
⚫Be sure to observe the expiration date (3 years from manufacturing).
❺Attach fixing elements after required curing time
・Estimated Curing Time
Temperature (℃) -20 -10 -5 0 5 10 15 20 25 30
Curing time
(Minute)		 In the air 720 180 100 60 40 25 18 15 12 10
Under water – – – 120 80 50 36 30 24 20
※This curing time is a guideline for achieving about 80% of maximum strength

AP Type

強度表をPDFで開く
Unit：mm Unit：kN
Bolt Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
M 8 AP-8  70 5.9 8.9
M10 AP-10 90 9.4 14.2
M12 AP-12 100 13.7 20.6
M16 AP-16 130 25.4 38.1
M20 AP-20 200 38.3 57.5
M22 AP-22 250 47.4 71.2
M24 AP-24 300 55.3 82.9
M30 AP-30 350 87.8 131.8
M36 AP-36 400 119.4 179.1
M20 AP-2016 160 38.3 57.5

AP Type

強度表をPDFで開く
Unit：mm Unit：kN
Deformed bar Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
― ― ― ― ―
D10 AP-10 90 12.0 18.0
D13 AP-12 100 15.1 22.6
D16 AP-16 130 25.4 38.1
D19 AP-20 200 44.5 66.8
D22 AP-22 250 55.8 83.8
D25 AP-24 300 71.8 107.7
D32 AP-30 350 101.7 152.6
D38 AP-36 400 126.0 189.0
D19 AP-2016 160 35.6 53.5

AP-S Type

強度表をPDFで開く
Unit：mm Unit：kN
Bolt Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
M10 AP-10S 50 4.0 6.0
M12 AP-12S 60 5.7 8.6
M16 AP-16S 85 11.4 17.2
M20 AP-20S 130 26.1 39.1
M22 AP-22S 165 41.3 61.9
M24 AP-24S 195 47.5 71.3
M30 AP-30S 230 62.6 94.0
M36 AP-36S 260 77.6 116.4

AP-S Type

強度表をPDFで開く
Unit：mm Unit：kN
Deformed bar Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
D10 AP-10S 50 4.0 6.0
D13 AP-12S 60 6.7 10.1
D16 AP-16S 85 11.4 17.2
D19 AP-20S 130 25.9 38.9
D22 AP-22S 165 36.8 55.3
D25 AP-24S 195 46.6 70.0
D32 AP-30S 230 66.8 100.3
D38 AP-36S 260 81.2 121.8

AP-L Type

強度表をPDFで開く
Unit：mm Unit：kN
Bolt Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
M10 AP-10L 120 9.4 14.2
M12 AP-12L 145 13.7 20.6
M16 AP-16L 185 25.6 38.4
M20 AP-20L 245 38.3 57.5
M22 AP-22L 280 47.4 71.2
M24 AP-24L 345 55.3 82.9

AP-L Type

強度表をPDFで開く
Unit：mm Unit：kN
Deformed bar Item no. Drilling depth Allowable tensile load
(long term)		 Allowable tensile load
(short term)
D10 AP-10L 120 14.0 21.0
D13 AP-12L 145 24.9 37.3
D16 AP-16L 185 39.0 58.5
D19 AP-20L 245 54.6 81.9
D22 AP-22L 280 62.5 93.8
D25 AP-24L 345 82.5 123.8
・The allowable load differs depending on the rod material, type, concrete strength, and embedding conditions. Please perform strength calculation according to the actual installation conditions
・The allowable tensile load is a calculated value according to the manufacturer’s formula. The allowable load is the calculated value of the concrete failure mode when using Fc = 21N / mm2 concrete, M screws (SS400) and deformed bar SD295 (use SD345 for above D19)

AP TYPE / GLASS CAPSULE: VINYL ESTER RESIN
…JCAA Certified　…SHASE-S Standard
サイズ表をPDFで開く

Open chart in PDF

Unit：mm Unit：pc
D Item no. L Content
㎤		 Threaded Rod
Deformed bar		 Drilling
diameter		 Drilling depth Qty・per
Box Medium box Carton
8.0 AP-8 70 2.7 Ｍ8 9.0 70 20 100 1,000
10.5 AP-10 90 6.3 M10 12.0 90 20 100 1,000
10.5 AP-10 90 6.3 D10 13.0 90 20 100 1,000
13.0 AP-12 95 9.5 M12 14.5 100 20 100 1,000
13.0 AP-12 95 9.5 Ｄ13 16.0 100 20 100 1,000
17.0 AP-16 125 21.5 Ｍ16 19.0 130 20 100 500
17.0 AP-16 125 21.5 Ｄ16 20.0 130 20 100 500
20.0 AP-20 195 50.3 Ｍ20 24.0 200 10 50 200
20.0 AP-20 195 50.3 Ｄ19 25.0 200 10 50 200
24.0 AP-22 245 90.0 Ｍ22 28.0 250 5 20 100
24.0 AP-22 245 90.0 Ｄ22 30.0 250 5 20 100
28.0 AP-24 280 148.0 Ｍ24 32.0 300 5 10 50
28.0 AP-24 280 148.0 Ｄ25 34.0 300 5 10 50
35.0 AP-30 330 276.0 Ｍ30 40.0 350 – 5 30
35.0 AP-30 330 276.0 Ｄ32 42.0 350 – 5 30
40.0 AP-36 400 447.0 Ｍ36 48.0 400 – 5 20
40.0 AP-36 400 447.0 Ｄ38 50.0 400 – 5 20
20.0 AP-2016 160 41.0 Ｍ20 24.0 160 10 50 200
20.0 AP-2016 160 41.0 Ｄ19 25.0 160 10 50 200
AP-S TYPE / GLASS CAPSULE: VINYL ESTER RESIN
サイズ表をPDFで開く

Open chart in PDF

Unit：mm Unit：pc
D Item no. L Content
㎤		 Threaded Rod
Deformed bar		 Drilling
diameter		 Drilling depth Qty・per
Box Medium box Carton
10.5 AP-10S 65 3.8 M10 12.0 50 20 100 1,000
10.5 AP-10S 65 3.8 D10 13.0 50 20 100 1,000
13.0 AP-12S 65 6.0 M12 14.5 60 20 100 1,000
13.0 AP-12S 65 6.0 Ｄ13 16.0 65 20 100 1,000
17.0 AP-16S 95 14.4 Ｍ16 19.0 85 20 100 500
17.0 AP-16S 95 14.4 Ｄ16 20.0 85 20 100 500
20.0 AP-20S 140 32.0 Ｍ20 24.0 130 10 50 200
20.0 AP-20S 140 32.0 Ｄ19 25.0 130 10 50 200
24.0 AP-22S 180 61.0 Ｍ22 28.0 165 5 20 100
24.0 AP-22S 180 61.0 Ｄ22 30.0 165 5 20 100
28.0 AP-24S 195 98.0 Ｍ24 32.0 195 5 10 50
28.0 AP-24S 195 98.0 Ｄ25 34.0 195 5 10 50
35.0 AP-30S 220 190.0 Ｍ30 40.0 230 – 5 30
35.0 AP-30S 220 190.0 Ｄ32 42.0 230 – 5 30
40.0 AP-36S 260 293.0 Ｍ36 48.0 260 – 5 30
40.0 AP-36S 260 293.0 Ｄ38 50.0 260 – 5 30
AP-L TYPE / GLASS CAPSULE: VINYL ESTER RESIN
サイズ表をPDFで開く

Open chart in PDF

Unit：mm Unit：pc
D Item no. L Content
㎤		 Threaded Rod
Deformed bar		 Drilling
diameter		 Drilling depth Qty・per
Box Medium box Carton
10.5 AP-10L 125 9.2 M10 12.0 120 20 100 1,000
10.5 AP-10L 125 9.2 D10 13.0 120 20 100 1,000
13.0 AP-12L 135 14.9 M12 14.5 145 20 100 600
13.0 AP-12L 135 14.9 Ｄ13 16.0 145 20 100 600
17.0 AP-16L 170 30.0 Ｍ16 19.0 185 20 100 200
17.0 AP-16L 170 30.0 Ｄ16 20.0 185 20 100 200
20.0 AP-20L 230 59.3 Ｍ20 24.0 245 10 50 100
20.0 AP-20L 230 59.3 Ｄ19 25.0 245 10 50 100
24.0 AP-22L 280 106.7 Ｍ22 28.0 280 5 20 100
24.0 AP-22L 280 106.7 Ｄ22 30.0 280 5 20 100
28.0 AP-24L 325 170.0 Ｍ24 32.0 345 5 10 50
28.0 AP-24L 325 170.0 Ｄ25 34.0 345 5 10 50

【Drilling】
Anchor Drill Bit [ADXⅡ-HEX Type] [ADXⅡ-MAX Type]
Click here for detail ☞
【Cleaning】
Dust Pump [P Type]
Click here for detail ☞
Dust Brush [H Type]
Click here for detail ☞
Dust Brush [W Type]
Click here for detail ☞
【Marking】
DK Socket (For deformed steel rods)
Click here for detail ☞
【Insert/Installation】
Attachment [CA]
Click here for detail ☞
・Use commercially available sockets for all threaded rod